Покриття з композиційного квазікристалічного сплаву на основі алюмінію

Д.В. Гущик; О.І. Юркова; О.В. Бякова; С.О. Наконечний

doi:10.15407/mom2018.01.053

Authors

D.V. Hushchyk National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, Kyiv
A.I. Yurkova National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, Kyiv
A.V. Byakova I. M. Frantsevich Institute for Problems of Materials Science, NAS of Ukraine, Kyiv
S.O. Nakonechnyy National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, Kyiv

DOI:

https://doi.org/10.15407/mom2018.01.053

Abstract

The structure, phase composition, and mechanical properties of composite quasicrystalline Al-Fe-Cr based coatings obtained by cold-spraying (CS) process on a steel substrate were studied. The effectiveness of the CS process from the point of view of the complete conservation of metastable quasicrystalline i-phase particles in an aluminium matrix is demonstrated, which provides a combination of high strength and sufficient plasticity necessary for the use of coatings in engineering practice.

References

Barthes-Labrousse M-G., Dubois J-M.,Philos. Mag, 2008, Vol. 88, pp. 2217 –2225.

https://doi.org/10.1080/14786430802023036

Inoue A., Kimura H., Mater. Sci. Eng. A, 2000, Vol. 286, pp. 1 –10.

https://doi.org/10.1016/S0921-5093(00)00656-0

Dubois J-M. Chem. Soc. Rev., 2012, Vol. 41, pp. 6760 – 6777.

https://doi.org/10.1039/c2cs35110b

Khun N.W., Li R.T., Khor K.A., Tribology Trans., 2015, Vol. 58, pp. 859 – 866.

https://doi.org/10.1080/10402004.2015.1023411

Byakova A.B., Yurkova A.I., Vlasov A.A., Metallofiz. Noveishie Tekhnol., 2015, Vol. 37, No 7, pp. 1001 – 1018.

Milman Yu.V., Sirko A.I., Iefimov М.О., High Temp. Mater. Processes, 2006, Vol. 25, pp. 19 – 30.

https://doi.org/10.1515/HTMP.2006.25.1-2.19

Milman Yu.V., Mater. Sci. Forum, 2005, Vol. 482, pp. 77 –82.

https://doi.org/10.4028/www.scientific.net/MSF.482.77

Davis J.R. Handbook of Thermal Spray Technology, OH: Materials Park, 2004, 338 p.

Alhimov А.P., Kosarev V.F., and Plohov A.V. Scientific basis for technology of cold spray process and properties of sprayed materials. – Novosibirsk.: NGTU, 2006, 280 p.

Li W.-Y., Liao H.-L., Li C.-J., Li G., Coddet C., Wang X.-F., Appl. Surf. Sci., 2006, Vol. 253, pp. 2852 – 2862.

https://doi.org/10.1016/j.apsusc.2006.05.126

Li Wen-Ya, Zhang Chao, Guo Xueping, Li Chang-Jiu, Appl. Surf. Sci., 2007, Vol. 254, No 2, pp. 517 – 526.

https://doi.org/10.1016/j.apsusc.2007.06.026

Cahn J.W., Shechtman D., Gratias D., Mat. Res. Soc., 1986, Vol. 1, pp.13 – 26.

https://doi.org/10.1557/JMR.1986.0013

Milman Yu.V., Galanov B.A., Chugunova S.I. Acta Met. Mater., 1993,Vol.41, No 9, pp. 2523 – 2531.

https://doi.org/10.1016/0956-7151(93)90122-9

Galanov B.A., Milman Yu.V., Chugunova S.I., Goncharova I.V., Superhard materials, 1999, No 3, pp. 23 –25.

ISO 14577-1:2015(E). Instrumented indentation test for hardness and materials parameters, 2015, 46 p.